replica brand jewelry wholesale HL line cutting operation and use

28 four jewelry wholesale After the power is applied, the computer can quickly enter the system and select 1. Run runs, press Enter to enter the main menu. Under the main menu, the corresponding operation can be moved or pressing the red letters on the corresponding menu. Before cutting workpieces, the 3B instruction file of the workpiece must be transferred to the virtual disk processing file area. The so -called virtual disk processing file area is actually a temporary storage area of ​​the processing instructions.
The operation is as follows:
First of all, press the F key under the main menu, and then make the following operations according to the adjustment path:
① adjust from the gallery WS -C:
Pay back to return The car key, the cursor is moved to the required file, press Enter, and exit for ESC.
Note: The gallery WS -C is where the file is stored in the system, and it can store up to about 300 files. Replacement integrated integrated blocks with higher integration can be expanded to about 1,200 files. The documents that are stored in the gallery have been retained for a long time, and the files stored in the virtual disk are automatically cleared after shutting down or pressing the reset key.
②Cap to the hard disk:
Press F4, then press D, move the cursor to the required file, press F3, move the cursor to the virtual disk, press Enter, and then exit at ESC.
③ Moved from the floppy disk:
Press F4, insert the floppy disk, press A, move the cursor to the required file, press F3, move the cursor to the virtual disk, press Enter key, and then exit for ESC.
Note: Use the F3 key to transfer the file between the gallery, hard disk, and software disk. This system does not use hard disks and soft disks, and can also work normally with the gallery WS -C alone.
④ Modify 3B instructions:
Sometimes you need to temporarily modify a segment 3B instruction. The operation method is as follows: Under the main menu, press the F key, move the cursor to 3B files that need to be modified, press Enter key, display 3B instructions, press the INSERT key, use the upper, lower, left, right arrow keys, PGUP and pgdn The key can check and modify the 3B instructions, after modification, and exit for the ESC.
⑤ manual input 3B instructions:
Sometimes cutting some simple workpieces, such as a circle or a square, do not need to be programmed, you can directly enter the 3B instructions by manual, the operation method is as follows:
on the main menu on the main menu Press the B key, press the Enter key, and then pass the 3B instructions in the standard format.
For example:: If the coordinate value is zero, it can be omitted.
, for example:. After entering one, press the Enter key, then enter the next one, enter the input, and exit at ESC. The manual input instruction is automatically named NON. B.
⑥ Browse gallery:
This system has the function of browsing the gallery, which can quickly find the required files. The operation is as follows:
Plip the TAB key under the main menu, and automatically display the gallery in turn in turn in sequence Graphic and corresponding 3B instruction file names. Press the empty key to pause and press the empty key to continue. Before the formal cutting is adjusted, for the sake of insurance, it is advanced to simulate the cutting to observe whether the graphics (especially the taper and the upper and lower alien workpieces) and the zero -zero coordinates are correct. Essence The operation is as follows:
① Press X under the main menu to display the virtual disk processing file (3B instruction file). If there is no file, you must return the main menu to adjust the file (see the file to be adjusted into the section).
② Move the cursor to 3B instruction files that need to be simulated, press Enter to show the graphic of the processing container. If the ratio of the graphic is too large or too small, it is not easy to observe. You can adjust the , -key. If the position of the graphic is not right, you can adjust the upper, lower, left, right arrow keys, PGUP and PGDN keys.
③ If it is a general workpiece (that is, non -conical degree, non -upper and lower alien workpieces), you can press F4 and Enter to display the end point X and Y back to zero coordinates.
④ taper or upper and lower alien workpieces must be observed to observe the cutting trajectory above. Press F3 to display the simulation parameter settings sub -menu. The speed limit is the simulation cutting speed. Generally, the maximum value is 4096, and the left and right arrow keys can be adjusted. Press G and Enter to set the sub -menu to enter the cone parameter, as follows:
This Set the sub -menu:
Degree cone degree -1. Set the cone angle [Note 1]
file2 Alien file -2. Press the [ENTER] key to select the file above [Note 2]
Width The workpiece thick 3. If the workpiece is thick, refer to Figure 1
base reference surface height -4. The distance between the size and the lower guide wheel, refer to Figure 1
heighht rumor -5. The distance between the machine tool (center of the guide wheel), refer to Figure 1
idler guide wheel radius -6. The radius of the guide wheel (for cutting points for compensation), it can be set to 0 [Note 3]
vmode cone mode — 7. Sectional mechanism mode: Small trailer/swing guide wheel/shake wire shelf [Note 4]
rmin waiting for round radius -8. Waiting for the circular radius (minimum R value), the arc of the processing graph that is small than the R value will be equal. Calculation calculation -9. For the reference height Base and the wire rack distance Height, it is more positive. [Note 6]
Setting method: After pressing the Enter key, enter the value (unit: 1: angle, 3, 4, 5, 6, 7: mm).
press Enter the car.
[Note 1]: The cone angle is unilateral, the unit is the degree, decimal. If non -decimal, first convert to decimal (example: 1 ° 30 = 1.5 °).
This When cutting counterclockwise, take the small lower part (positive cone) on the positive angle. When cutting clockwise, the situation is the opposite. This system can be cut in pangoscope. Refer to Affective Example 1.
[Note 2]: Select this menu for upper and lower alien processing. File2 is a graphic on the workpiece. Move the cursor to the required file, press Enter, adjust the above graphic file, and press ESC to display the upper and lower up and down to display the upper and lower up and down Graphs superimposed. Refer to Affective Example 2.
[Note 3]: For cut offset compensation, the radius value of the input wheel can be entered.
[Note 4]: Modify three times. For the taper mechanism of the small trailer and the swing guide wheel mode, the system compensates both the point cut point of the guide wheel to the U and V. For the swing wire mode, it only compensated U to the point cut point of the guide wheel.
[Note 5]: Once the arc radius value is entered, the arc with a radius of the arc value of the arc in the workpiece will be cut with arc values ​​such as the radius of the arc. If you only want to specify an arc cutting such as an arc, the rest are cut according to the normal cone, and you can insert the ER letters in front of the 3B instruction section of the 3B instruction file. Capted.
[Note 6]: When the measuring wire frame and the benchmark surface are not very accurate (required to be as accurate as possible), you can first cut a taper cylindrical body, and then measure the upper and lower diameter of the conical cylindrical body, enter the input, enter the input The computer can automatically calculate the accurate wire rack and the benchmark surface.
After the cone parameter is set, press ESC to exit, press the F1, Enter key, and then press Enter to start simulation cutting. After cutting, display the end point coordinate value x, y, u, and V. UMAX and VMAX are the maximum movement distance during cutting the UV axis, and this value should not exceed the maximum allowable itinerary of the UV axis. After the simulation cutting is over, press the empty key, E and ESC to return to the main menu. After the simulation cutting is correct, the workers are installed, and the wire tube, pump, and high frequency are turned on. It can be formally cut.
① In the main menu, choose to process#1 (only one control card can only be processed#1. When installing multiple control cards at the same time, you can choose to process#2, processing#3, processing#4), processing Press the Enter key and C to display the processing file.
② Move the cursor to the 3B file to be cut, press Enter to show the graphics of the 3B instruction, adjust the size ratio and appropriate position (refer to the section of simulation processing).
③ Press F3 to display the processing parameter settings as follows:
The processing parameter settings:
v. F. Inverter -1. When cutting the gap between molybdenum wire and workpiece, the larger the value, the tighter the tracking
offset compensation value -2. Set the compensation value/offset, [Note 1]
Grade cones value -3. Press the [ENTER] key, set the taper settings sub -menu [Note 2]
ratio processing ratio -4. Graphic processing ratio
axis coordinates conversion -5. Optional eight coordinates conversion, including mirror conversion
loop recycling processing -6. The number of circulation processing, 1: once, 2: twice, up to 255 times
speed step speed -7. Enter the Step Speed ​​Speed ​​Set Sub -menu [Note 3]
XYUV Dragon Tune -8. Enter the trailer adjustment menu
Process control -9. Press the [ENTER] key to enter the control sub -menu
hlet machine -10. The actual working hours of the machine tool
Setting method:
1.5.6.7.8.9. Press [Enter], [Pageup], [PageDown] or left and right arrow keys
2.3.4. After [ENTER], the input value (unit: 2: mm, 3: angle)
This Speed ​​Set Set Sub -menu:
xy speed speed -1. The maximum feed speed (unit: μ/second, the same below)
uv speed speed -2. The maximum feed speed at the time of UV axis
xy limit speed limit — 3. The maximum feed speed when the XY axis moves quickly
uv limit speed limit — 4. R n Tuning method: Press [ENTER], [Pageup], [PageDown] or left and right arrow keys
Dragon plate adjustment menu:
xy trailer plate adjustment -1. Tune/Move XY Dragon [Note 5]
uv trailer adjustment -2. Tune/Move UV Dragon [Note 5]
motor step distance angle -3. Set the step distance angle of the machine tool step system [Note 4]
3/3: three phases and three shots
6/3: three phases and six shots
10/5: Five phases
5axis .. 6/3: Five -axis control
The adjustment method:
1.2. After [ENTER], the arrow key is adjusted. Press three consecutive [ENTER] to change the
Process parameter settings:
The retreat 0 SEC -1. Short -circuit retirement selection [Note 6]
短 短 0 SEC — 2. Select the corner time [Note 7]
automatically stop on -3. Automatically stop setting on or off [Note 8]
[Note 1]: Compensation method: Following the direction of cutting forward, the molybdenum wire shifts to the left to take positive compensation, and the molybdenum wire is offset to the right. No need to transition, but it must be closed. If the molybdenum wire offset compensation has been made during programming, the compensation cannot be compensated here, and it should be set to 0.
[Note 2]: The cone settings refer to the simulation processing section.
[Note 3]: Limit speed limit is to prevent the speed of the motor too fast when the trailer is quickly moved and causes a stroll. The speed limit values ​​of different types of machine tools are different and can be obtained through practice. The speed limit value should not be changed casually after setting. SPEED speed is the highest feed speed of the actual work of the trailer. Set the appropriate speed with variable frequency adjustment (V.f.), Which can make the cut tracking stable. The thicker the workpiece, the smaller the step speed of the steps, and the adjustment can be adjusted during processing.
[Note 4]: The working method of the steps of the step -to -step motor is fixed for each type of machine tool. Once set, do not change it at will, otherwise the workpiece will be scrapped. Therefore, for the sake of insurance, you must press the car bond for three consecutive times to change.
[Note 5]: After pressing the Enter key, press the up, down, left and right arrow keys to move X, Y, U, and V dragging board, click one step (for maintenance). Move (for correction workpieces).
If in the return key, enter the value, turn on high frequency, feed, and this value can be cut as a straight line instruction.
[Note 6]: Short -circuent selection, each press Enter for 5 seconds (SEC), the maximum is 35 seconds. How many seconds occurred at this time and automatically returned after the short circuit, and immediately recovered automatically after the short circuit disappeared. If the short circuit is not excluded for 1 minute, the alarm is automatically stopped. When setting an OSEC (0 seconds), manual return, that is, manual operations need to enter the retreat when short circuit, and the manual operation of manual operation after short circuit will return to advance. If there is no artificial intervention after a short circuit, the police will be stopped automatically.
[Note 7]: The time of the high frequency stay after each section is processed, for clearing the corner, the corner time selection, and set to 0SEC (0 seconds) to have no clear angle function. The maximum is 15 seconds for each press Enter for 1 second.
[Note 8]: Set up automatically, press Enter key to select the automatic stop function on or off.
④ The parameters of each parameter are set, and the ESC exits. Press F1 to display the starting section 1, indicating that cutting from the first paragraph. (If you want to cut from the nn section, press the clear key to remove 1 word and then enter the number n). Then press Enter the end point of XX. (Similarly, if you want to end in the m -segment, use the clearance key to remove the XX, then enter the number M), and then press the Enter key.
⑤ Press F12 to lock in (enter the menu to light green from the blue background, then press F12, then from light green to blue, loosen and give) Press F1 0 to select automatic (the menu light green bottom is automatic, then press f10, then press F10 , From light green to blue to manual) Press F11 to open high frequency and start cutting. (Press F11 as a high frequency).
⑥ During the process of cutting the process:
a, the tracking unstable
Press F3, adjust the frequency conversion (V.F.) value of the left and right arrows until the tracking stability until the stability of the tracking stability Essence When the tracking of the cutting thickness is difficult to adjust, the step speed value can be lowered before adjusting until the tracking is stable. After adjusting, press ESC to exit.
b, short -circuit back
When a short circuit occurs, if the parameter is set automatically, after a few seconds (determined by setting numbers), the system will automatically return, and the short -circuit exclusion will automatically return to advance. The short -circuit has not been excluded after the short circuit continues to return, and the police will be stopped automatically. If the parameter is set to manual retreat, it is necessary to handle it manually: press the space key first, and then press B to enter the retreat. After the short circuit is eliminated, press the empty key and press F to recover. If the short -circuit time lasted for 1 minute, no one is dealt with, and the alarm is automatically stopped.
c, temporary suspension
Plip the empty key to pause, press the C key to restore processing.
d, set the setting when the segment is cut, press the F key, and then press f to cancel.
e, the midway power outage
Is when cutting the power out of power, the system automatically protects the data. After re -power, the system automatically restores the working status before the power outage of each machine. First enter the first machine screen, and press C and F11 to restore processing. Then press ESC to exit. Then press the corresponding number key to enter the screen before the machine tool stopping, and press C and F11 to restore processing. Other push.
F, broken silk
Press the empty key, and then press W, Y, F11, F10, and automatically return the processing point of the processing.
g, exit processing
After processing, press E and ESC to exit the processing and return to the main menu. Press E and ESC in the middle of the processing key to exit the processing. If you want to recover after exiting, you can press [CTRL] to add W (1 machine) under the main menu. ] Add K.
⑦ Inverse cutting
The reverse cutting can be used after cutting in the middle of the cut. On the one hand, it can avoid repeated cutting and saving time, and on the other hand, it can avoid the decrease in pollution and accuracy caused by repeated cutting. Operation method: Select processing under the main menu, press Enter, C, adjust the instructions, press F2, Enter key, then press Enter, select automatic, open high frequency to cut.
⑧ automatic opposite center:
In the main menu, select processing, press Enter key, and then press F and F1 to automatically find the center of the circle or square hole. Pole radius. Press [Ctrl] to add the arrow key, then stop after touching, and display X and Y after stopping. This system provides two automatic programming systems: editing programming (session programming) and drawing programming. The specific operation can be referred to the instructions (attached). There are two points to pay attention to:
① Data deposit and program deposit disks during programming, just graphic file xx. DAT and 3B instruction file xx. 3B is stored in a virtual disk, and the virtual disk is not kept after shutting down or reset. Therefore, you need to store these files in the gallery or hard disk and software disk. You can see the graphic file and 3B instruction file of the newly programmed, move the cursor to the file, press F3, and then select the gallery or hard disk, soft disk, and press the Enter key.
② When programming, if you want to mix the graphic file (xx.dat) in the gallery or hard disk, soft disk, you should first adjust the graphic file to the virtual disk. Press the T key under the main menu, insert a disk equipped with a DXF format or G format file, and then follow the prompt operation. The DXF file must be the DXF format of AutoCAD R12. When the valid number is greater than 500, the DAT file is automatically divided into multiple files.
The user can also use the "data interface" of programming Towedm to directly read the DXF format file. In this way, the DXF file is processed. There is no limit on the number of paragraphs and can also support the R14 and R2000 versions of AutoCAD. Please refer to section 1.1 of the next chapter "TowedM Cutting Programming System User Guide".
1.1 Main menu
Ness control program --- Enter the CNC program menu (see Chapter 4) and perform CNC processing routes. rn数据接口---- 根据会话区提示，选择：rn1. DXF文件并入: 将AutoCAD的Dxf格式图形文件并入当前正在编辑的线切割图形文件，支持点、线、 The conversion of multi -segment, polygon, round, arc, and ellipse supports the R14 and R2000 versions of AutoCAD.
2. Output DXF file: Output the currently edited wire -cut graphics file output into the DXF format file of AutoCAD, and the data point is also saved.
3. 3b merged: incorporate the existing 3B files as graphics files.
4. YH merges: merged into the graphic file in YH2.0 format.
The advanced curve ---- Enter the high-level curve menu (see Verse 2.4).
The above screen-restore the previous screen. When the graphic is enlarged or reduced, the previous graphic state is restored with this menu.
In the file-enter the file manager (see Section 1.3), read the graphical data file (DAT file) in the disk for re-editing. You can create new files by opening a unprecedented graphic file.
Themo-in-the file-enter the file manager (see section 1.3) and incorporate a graphic data file, which is equivalent to the "disk file" of the old autop.
File deposit ---- The graphic file deposit currently edited. The graphic data file after saving is called the current file name, with DAT as the suffix. If there is no file name, enter the file manager (see Section 1.3), you can directly type the file name.
The files are stored separately to enter the file manager (see Section 1.3), and replace the currently edited line-cut graphics file. The current file name after saving is a new file name. Equivalent to AUTOP's "file renaming".
Printing ---- Printing function is to output the current screen display in place file file "$ $ $. BMP".
exit system ---- Exit the graphic state.
The temporary storage system ---- When running in Win98, it is used to switch the operating program.
1.2 fixed menu
-enter the order menu (see Section 2.1).
-straight-enter straight menu (see verse 2.2).
round-enter the round menu (see section 2.3).
Windows ---- The graphic amplification display in the rectangle (window) will be selected.
Interruption ---- To execute the interruption first, you must determine that there are two points on the straight line, circle, or circle you want to interrupt. The chart part of the two points where the cursor is in the execution is cut off. If the CTRL key is pressed in advance before executing the interrupt operation, the execution will be interrupted reverse. At this time, the chart between the two points of the light target was retained and the rest was cut off. The auxiliary line cannot be interrupted.
The intersection point ---- capture the intersection point, and the intersection point is required to be within the two-phase intercourse.
Munning cursor until you need to see near the point, press Enter or left mouse button to automatically find an accurate intersection. After the operation, press the [ESC] key to terminate.
It can not be used in advance when picking up the point, and directly select the handling of the picture.
The deletion ---- Delete geometric elements, right, straight, round, arc to delete, type ALL Enter, all graphics will be deleted. On the element, press the ENTER key or left mouse button. After the operation, press the [ESC] key to terminate.
Cancelled ---- Cancel the previous operation. If you draw a chart in the previous operation, delete it. If the previous operation is deleted, it will restore it.
This session area prompts as follows:
to cancel the graphic input in the previous step;
>: Y
This renewed ---- The graphic or other operation deleted from the last time the last time the operation is canceled. The deleted graphic recovery, or delete the previous cancellation of the recovery of the operation recovery. Only support one step to re -operate.
Reference ---- Establish a user reference coordinate system.
Relative ---- Enter the relative menu (see Section 3.2).
-enter the block menu (see Section 3.1).
Query ---- Query point, straight line, round, arc geometric information
The tips as follows:
Query (point, line, round, arc) =
Select the geometric element, the information format is as follows:
1. Click xo = horizontal coordinate yo = vertical coordinates
2. Auxiliary line xo = Reference point horizontal coordinate yo = Reference point vertical coordinate A = angle n3 . Straight X1 = First Point Settlement Y1 = First Point Venture
x2 = Second point horizontal coordinate y2 = 2 point vertical coordinates
a = angle l = length
4. Yuan xo = Yuanxin Health coordinates yo = Yuanxin Venture R = radius
5. Arc xo = Yuanxin Hengxin coordinates yo = Yuanxin Venture R = radius
a1 = Starting point angle A2 = Termination point angle n Full screen full screen ---- Display the entire graphics on the screen
A shrinking ---- Reproduce the graphic and zoom into the display by the input reduction multiple. In addition to narrowing and magnifying the figure above, you can also press PageDown to execute the shrinking and Pageup execution of the amplification function in any time in the picture.
Movement-drag display graphics
Operation method: execute the movement function, press the mouse to determine the key or knocking the car key when the cursor is the cross line, so that the cursor becomes a four-way arrow. Move the cursor to drag the graphics.
It to end the dragging state, just press the mouse to determine the key or tap the Enter key again. The cursor will be changed to the original cross line graphics at the same time. You can also press the CTRL arrow key for any time in the drawing to perform the movement operation.
Clear screen-hide all graphics.
The return-return to the main menu and display the current file name in the session area.
1.3 File Manager
The file manager In addition to the read and deposit of the file, it can also be previewed and file sorting. The operation is as follows:
↑ ↓ ← →: The arrow keys are used to select the existing files, and you can also use the mouse to click to select. The "Preview Area" can preview the selected file in real time.
DELETE: Delete the selected file.
f6: Sort by file name.
f7: Sort by time.
tab: Switch the area to be modified. Every time the TAB key is pressed, the modified area is switched between the folder, file name, and telephone. The switching area is displayed in green, and you can also click the area to be modified with a mouse. The user can use the keyboard at this time to modify the content in the green area.
f4: Convert folder. Every time the F4 key is pressed, the current folder is converted between D: WSNCP (hard disk) and the folder (virtual disk) when the program enters. If the system is not equipped with a hard disk, D: WSNCP is also a virtual disk.
S specific operation examples:
1. Open and merge an existing file: Use the mouse or ↑ ↓ ← → arrow key to select a file name in the "File List Area", click "Open" or press Enter You can also double -click a file name in the "File List Area" in the mouse.
2. Open a non -existent file: Use the mouse to click or the TAB key to switch to make the "file name area" turning green, type the file name, click "Open" or "load", or press Enter.
3. File deposit and files are stored separately: Use the mouse to click or the TAB key to switch to make the "file name area" turning green, type the file name, and click "Save" or press the ENTER key. You can also select a existing file name in the "File List Area", and then "save". At this time, it will prompt "cover the old file Y/n?", Please answer (y) or (n) as needed.
4. Change the folder: Use the mouse to click or the TAB key to switch to make the "folder area" turning green, type the known folder (such as E:, F: File, etc.). You can also simply press the F4 key to switch between two fixed folders.
[Note]: If there is no change folder, all files are only stored in a virtual disk, and it will not be saved after power outage. Users must save the file from the virtual disk into the gallery in the HL system.
1.4 shortcut keys, mouse keys definition
towedm can also use shortcut keys, directly press the letters or numbers prompted by the "shortcut key à" in the session area to quickly select the corresponding menu operation.
For convenience, Towedm also provides the following shortcut keys:
home: Accelerate the movement of the cursor
end: Slow down the cursor movement speed.
pageup: magnify graphics.
pagedown: Reduce graphics. r ↑: Move the cursor upward.
↓: Move the cursor downward.
←: Move the cursor to the left.
→: Move the cursor to the right.
ctrl ↑: Move the graphs upwards.
ctrl ↓: Move the graphs down.
ctrl ←: Move the graph to the left.
ctrl →: Move the graph to the right.
The shortcut keys to select the original point are letters O.
The shortcut key to select the axis X is X.
The shortcut key to select the axis y is Y.
F2: Back to the main menu, and display the current file name in the session area.
f3: Call the calculator (see Section 1.5).
F4: Refresh the graphic without drawing points.
F5: Refresh the graph (drawing point, drawing auxiliary line).
F6: Refresh the graphic without drawing auxiliary lines.
f10: Rebcing processing route.
Mouse key definition: Towedm defines the "confirmation key" by defining the left mouse button by default, and the right button is defined as "cancellation key". When answering "y/n?", Press the "Confirmation Key" to indicate "Y", press the "Cancel" to indicate "n", and press the middle key to indicate "ESC" cancel.
1.5 Calculator ---- Press the F3 key to use the calculator function.
towedm calculator, you can calculate ( ), (-), multiplication (*), division (/), multiplication (^), and triangle function sine (SIN), Yu Xian (cos), positive cut (TAN), CTA, ASIN, ACOS, ATAN). To call the calculation result of the previous calculator, you can press the key "?"
. In addition, you can also use the calculator function at any time of the data entry, that is, use the above operator when entering the data. two. The graphics input operation
towedm's graphics menu is a little, straight, round, and high -level curves included.